Error code
Dishwasher error code F-2
Dacor dishwasher error code F-2: The control asked for the wash pump and the board did not confirm that it had been switched on. Which machines can raise it, what the maker publishes about it, and what to do next.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
What we can confirm
Code F-2, from the manufacturer's own documentation
A code is only meaningful together with the machine showing it — the same digits mean different things on different equipment.
The code
F-2
The control asked for the wash pump and the board did not confirm that it had been switched on. That puts the problem between the control and the pump rather than necessarily in the pump itself, which is good news: a relay on the power board is a smaller matter than a motor. The wiring between the two boards on this platform is old enough now that connectors are always worth checking first.
or call (305) 363-6067
What it narrows down to
Circulation pump — the power board saw no relay closure.
Diagnostic
From $95, credited to the repair
On the same appliance
What else belongs to the dishwashers
On this make a code belongs to the appliance rather than to a product line. These are the other conditions this machine can display, and the models that can show this one — a display often has more than one thing to say, and the model number decides what any of it costs to put right.
Other codes this appliance can display
Inlet valve — after filling, the controller found no water where it expected some.
Electrical or heater — no temperature rise within the expected time during wash or rinse.
Drain pump — water was still present in the sump after the drain cycle.
Air flow fan.
Controller or floor guard — the leak-detection system has tripped.
EEPROM failure.
Communication failure — data transfer between the control board and the power board.
Water presence sensor — the WPS that reads water, turbidity and temperature.
Leakage check — a leak has been detected. Shut off the water supply and the breaker.
Water supply check — the valve is closed, the supply is suspended, or the inlet line is blocked.
Drain check — the machine could not empty properly.
High-temperature heating check.
The same digits mean different things on different equipment. Search the full code list
In more detail
About Dishwasher error code F-2
What F-2 means on this make
The control asked for the wash pump and the board did not confirm that it had been switched on. That puts the problem between the control and the pump rather than necessarily in the pump itself, which is good news: a relay on the power board is a smaller matter than a motor. The wiring between the two boards on this platform is old enough now that connectors are always worth checking first.
Where this appears, and which table it belongs to
On the appliance's own display. Photograph it before you cut the power: a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. Then check the model, because this make changed hands in 2016 and the two generations share no code string. The same characters mean different things on a Classic ERC oven, an ER-series range and a Modernist induction cooktop, and a meaning read off the wrong table is worse than no meaning at all.
Which machines this one applies to
EDW and IDW dishwashers. The same number on a different appliance of this make is a different page and often a different repair, which is why this archive is organized by appliance rather than by number. This maker documents codes on 5 of the appliance types this site publishes — coffee machine, cooktop, dishwasher, oven and range — and publishes none at all for freezer, microwave, range hood, refrigerator and wine cooler. Those appliances have symptom pages here and no code pages, which is the honest answer rather than borrowing a table from the machine next door.
What to do about it
- Note whether the machine is silent during the wash phase or makes a noise and achieves nothing.
- The harness and connectors between control and power board are inspected before parts are named.
- The relay is tested on the board; a failed relay does not need a whole new board on this platform.
- The pump itself is measured last, because it is the least likely of the three.
Where this goes next
The job this usually becomes is dishwasher drain and pump repair, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call (305) 363-6067 and describe what the panel is doing before booking anything.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards