Error code
Dishwasher error code F-6
Dacor dishwasher error code F-6: The machine believes water is where it should not be and has stopped itself. Which machines can raise it, what the maker publishes about it, and what to do next.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
What we can confirm
Code F-6, from the manufacturer's own documentation
A code is only meaningful together with the machine showing it — the same digits mean different things on different equipment.
The code
F-6
The machine believes water is where it should not be and has stopped itself. Under a panel-ready door in a fitted kitchen, that intervention is worth a great deal: the alternative is water finding the joinery and the floor below. It should never be reset and re-run to see whether it recurs. Either there is a leak, or the float or its switch has failed — and the first has to be excluded before the second is assumed.
or call (305) 363-6067
What it narrows down to
Controller or floor guard — the leak-detection system has tripped.
Diagnostic
From $95, credited to the repair
On the same appliance
What else belongs to the dishwashers
On this make a code belongs to the appliance rather than to a product line. These are the other conditions this machine can display, and the models that can show this one — a display often has more than one thing to say, and the model number decides what any of it costs to put right.
Other codes this appliance can display
Inlet valve — after filling, the controller found no water where it expected some.
Circulation pump — the power board saw no relay closure.
Electrical or heater — no temperature rise within the expected time during wash or rinse.
Drain pump — water was still present in the sump after the drain cycle.
Air flow fan.
EEPROM failure.
Communication failure — data transfer between the control board and the power board.
Water presence sensor — the WPS that reads water, turbidity and temperature.
Leakage check — a leak has been detected. Shut off the water supply and the breaker.
Water supply check — the valve is closed, the supply is suspended, or the inlet line is blocked.
Drain check — the machine could not empty properly.
High-temperature heating check.
The same digits mean different things on different equipment. Search the full code list
In more detail
About Dishwasher error code F-6
What F-6 means on this make
The machine believes water is where it should not be and has stopped itself. Under a panel-ready door in a fitted kitchen, that intervention is worth a great deal: the alternative is water finding the joinery and the floor below. It should never be reset and re-run to see whether it recurs. Either there is a leak, or the float or its switch has failed — and the first has to be excluded before the second is assumed.
Where this appears, and which table it belongs to
On the appliance's own display. Photograph it before you cut the power: a display that has been cleared has taken the evidence with it, and there is no way to ask the machine for it again. Then check the model, because this make changed hands in 2016 and the two generations share no code string. The same characters mean different things on a Classic ERC oven, an ER-series range and a Modernist induction cooktop, and a meaning read off the wrong table is worse than no meaning at all.
Which machines this one applies to
EDW and IDW dishwashers. The same number on a different appliance of this make is a different page and often a different repair, which is why this archive is organized by appliance rather than by number. This maker documents codes on 5 of the appliance types this site publishes — coffee machine, cooktop, dishwasher, oven and range — and publishes none at all for freezer, microwave, range hood, refrigerator and wine cooler. Those appliances have symptom pages here and no code pages, which is the honest answer rather than borrowing a table from the machine next door.
What to do about it
- Turn the water off at the supply valve and leave the machine alone.
- Look for water in the base tray and under the adjacent cabinets before anything is reset.
- Do not clear and re-run this code. If there is a leak, the machine stopping is the only good news in it.
- The float, the switch and the sources above them are checked as one job.
Where this goes next
The job this usually becomes is dishwasher leak repair, and that page carries a starting figure and the reasons that move it. If it turns out to be nothing — and on this make a real share of these are modes, reminders and settings rather than problems — the visit ends there and you pay the diagnostic and nothing else, or call (305) 363-6067 and describe what the panel is doing before booking anything.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards