Repair cost
Dacor gas burner and igniter repair cost
What gas burner and igniter repair costs on a Dacor in South Florida, from $155, and what moves that figure up or down. No final price is published anywhere on this site: the exact cost is confirmed on site after the diagnostic and agreed in writing before anything is opened.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
The short version
Where this figure comes from
A starting point for built-in appliances in South Florida, published so the number is not a mystery until somebody is standing in your kitchen.
Starts at
from $155
After a diagnostic from $95, which comes off the bill when you go ahead with the work.
or call (305) 363-6067
It is not
A quote for your unit
Exact cost
Confirmed after the on-site diagnostic
Warranty
On the labor we performed
What moves it
Why two of the same job cost different amounts
These apply at the same time and in both directions. Which of them is true of your kitchen is what the on-site diagnostic settles.
-
Clean or component
A cap seated wrong and a cracked igniter body present identically. The first costs nothing to correct and the second is a part; the difference is found by looking, not by ordering.
-
Whether the problem travels across the hob
Trouble confined to a single position stays with that burner. Trouble that moves around the hob points instead at the earth, the switch bank or the gas supply feeding all of them.
-
Standard burner or a pro brass one
The sealed brass burners on the rangetops are heavier, dearer, and carry a relight system absent from the ordinary hobs — three reasons the same symptom is not the same figure.
The work itself
What we actually do
The job behind the figure: what it involves, when a symptom points at it, and what we check first.
-
from $155 Gas burner and igniter repair
A burner that clicks without lighting, lights and goes out, or will not come down to a simmer. In Miami the usual culprits are salt air and humidity on the igniter, and a cap or head that went back slightly wrong after a clean — which is why so many of these calls date from the week the hob was scrubbed. The professional burners on the rangetops complicate it pleasantly: they are built to relight themselves after a draft or a boil-over, so a burner that keeps going out may be that system rather than the burner at all.
- Most of these problems begin the week the hob was deep-cleaned
- Salt air and humidity are what actually kill igniters here
- On the pro burners, repeated flame-outs may be the relight system
In more detail
About Dacor gas burner and igniter repair cost
Why this figure is a from
Ordinary parts in a salt-air city, and the figure is modest because a good share of these visits are resolved by reseating what came off during a clean rather than by fitting anything.
What we will not do
We do not quote a repair over the telephone from a description, and we do not publish a final price anywhere on this site. Both are the same rule. On this badge there is a second reason: almost everything this make sells is fitted into something — a column in a trim kit, a wall oven in a tall unit, a hood liner inside somebody else's millwork — and until the installation has been seen, half the estimate is missing. There is a third as well. This make changed hands in 2016, and an appliance from before that is a different repair with a different parts channel from one built after. We would rather establish both than guess at a number.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about Dacor gas burner and igniter repair cost
Why is it a from and not a price?
Because the same job is not the same work on two machines. On this badge there are two large variables before the part is even named: whether the appliance is captured by cabinetry, and which side of 2016 it was built. Either can change the hour, and the second can change the part number entirely. The exact cost is confirmed on site, in writing, before anything is opened.
Is the diagnostic on top of this?
The diagnostic is from $95 and it is credited toward the repair when you go ahead. Where the answer is that the machine is not worth fixing — or that a part for a discontinued platform is genuinely no longer made — you have paid for the answer and not for a part.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name